Videos are provided as a guide only. Refer to manufacturer
installation instructions and specs for complete information.

Today we are going to show you a little bit of wiring. Basically, like a wiring 101 and what to look for when you are going to hardwire into a vehicle. And what hardwire means is actually getting to the wires and splicing into them making a connection. We will go ahead and do our test and ground it. Instead of piercing the wires, if you have a junction that is easy to get to go ahead and pull it apart. And instead of piercing the wire, go ahead and test on the inside here. Just check each individual contact here until you hit something. Then make sure you actually have your running lights on and then go ahead and turn them back off. It also proves to us that our ground is good and it is working with our electrical system here.

If you know which tab is your running light, you can go ahead and look on the back side of it and have a hole on the backside of it that matches the front. In our case it looks it would be the purple wire here. So the purple wire here, we know is a running light so we can go ahead and make our connection to that wire right now. You always want to do your wiring one circuit at a time. Take your running light wire, which on a 4 pole would be brown, make your connection and make your ground connection too at this point. And then, test on the other side of the 4 pole at the end where you have your running lights working. So when you test this, you want to go ahead and put your ground to the ground pole on the 4 pole. Then go ahead and use the probe to go ahead and test the running light circuit here. Do that one at a time. Also basically everything applies to the other circuits too. Your left turn, your right turn, and brake, if you have a 5 wiring system, and your running lights.

Once you have found your running light circuit, then you go ahead and make your connection. Go ahead and start with your left turn signal. So we will go ahead and turn on our left turn signal. We will just repeat the same steps for testing for that. There you have it. Now if you notice that it is blinking real fast that is because the car thinks there is not a bulb hooked up to it, because there is not. Once you make your connection and plug it back into the tail light it will go back to normal. The same thing applies to the stop light circuit. So just have somebody hold down the break pedal and you just go ahead and go through them all until you find it. Then have them let off of it then turn it back on. The reason you do that is to verify that it is your stoplight circuit. Sometimes they have a constant 12 volts going to some other electronic in your vehicle. If you test it, turn everything off and on to verify that you have the right wire. Also the same thing applies when you go over to the passenger side and look for your right turn signal, do it the same way.


Why is Solder Paste Inspection Imperative?

Solder Paste Inspection is mainly completed to check the solder paste deposits in the Printed Circuit Board (aka PCB Board) fabricating process. It is known that most solder joint defects in a PWB assembly are arising from the wrong type of solder paste printing. Through the help of solder paste inspection (SPI), you could reduce the defects related to soldering by a considerable amount. This article can tell you the power of SPI process and how imperative it is .

Importance of Solder Paste Inspection Process

Below are some of the key points of information, which prove the importance of SPI process:

Lifts PCB Board Quality & Performance

This process takes advantage of cutting-edge equipment for exact inspection. Angle cameras are utilized to take 3-d pics, which are very useful in measuring the alignment and volume of the solder paste. It will help to increase the yield, in addition to the print quality. In addition, it will help improve the performance of the PCB Boards.

State-of-the-art Equipment for More effective Regulation & Checking

As explained earlier on, angle cameras are utilized, which deliver obvious 3D pics. Compared with the classic cameras, 3D cameras are capable of seizing the height of the solder paste printed. This encourages highly accurate measurement of the solder paste volume. Therefore, by utilizing SPI as well as automated optical inspection(AOI inspection), producers can easily keep an eye on and manage the component placement and solder paste printing processes.

Helps In Reducing Solder Errors

Crucial info about the printing process can be had by conducting the solder paste inspection. It offers a clear idea regarding the reasons for defects, and therefore letting you make the essential changes and lower the errors as low as possible.

All the points stated earlier make producers adopt the SPI process to fabricate high standard PCB Boards. The inspection process not only helps fabricate defect-free PCB Boards, but additionally saves substantial costs. On top of that, it additionally helps lessen the delivery time of the producers. This explains the value of solder paste inspection process. For an error-free solder, it is therefore, a good idea to adopt SPI.

For much more regarding Solder Paste Inspection, You ought to get it accomplished by a guru such as MOKO Technology. The company is positioned in China Shenzhen , and delivers services in solder paste inspection, as well as PCB Board design and fabricating.

Leave a Reply

Your email address will not be published. Required fields are marked *